Concrete & Masonry Products

All-Weather Blacktop Cold Patch

Blacktop patch

  • High performance patching material with good compaction for long-lasting repairs.
  • Use for the patch and repair of potholes in blacktop walks, drives, and parking lots.
  • Use in wet or dry conditions, in any temperature.
  • Ready-to-use, workable mix with high bonding characteristics.

Concrete Form Tubesbuilderstube

Concrete Post/Pole Footer Pads

Post pad 6x12

  • Precast concrete pad provides bearing at bottom of post or pole holes.
  • Saves time compared to pouring concrete and waiting for it to cure.

Expansion Joint

Plaster

USG No. 1 moulding plaster Plaster of Paris

Pea Pebbles

Pea gravel

Sand

Sand

Steel Reinforcing Bar

Fast-Setting Concrete Mix

Sakrete fast-setting

  • Sets in just 1/2 hour - much faster than regular concrete!
  • Set posts and poles without bracing or mixing.
  • Professional strength 5000 psi (pound per square inch) for commercial structural applications and superior durability.
  • Exceeds strength requirements of ASTM C 387.
  • Use for applications requiring at least 2 inches in thickness.
  • Click herefor more information.

Ready-Mix Concrete & Mortar

Sakrete concrete mix Sakrete sand mix Mortar mix

DAP® Ready-Mixed Concrete Patch

Dap concrete patch

  • Used to patch small cracks and breaks, or spot level concrete and masonry surfaces such as basement walls, patios, steps, sidewalks, and driveways.
  • Can be used as a “glue” to join broken pieces of concrete or brick.
  • Dries to a durable, hard finish.
  • Non-shrinking.
  • Interior/exterior use.
  • Gray.
  • Click herefor more information.

Damtite® Waterproof Cement-Based Coating

  • Waterproofs and protects building interiors from dampness, moisture, or seepage.
  • Ideal for interior or exterior, above or below grade; vertical, overhead, and non-traffic bearing surfaces.
  • Recommended for cast-in-place concrete, pre-cast concrete, brick, common block, stucco, unglazed terra cotta, porous stone, gunite, and other masonry substrates.
  • Locks water out or holds it in by actually becoming part of the wall.
  • Fills and seals pores and voids to correct surface irregularities.
  • Resistant to mold and mildew.
  • Compatible with a wide range of architectural coatings and textured finishes.
  • Comes in dry powder form; mix with water.
  • Cleans up with soap and water immediately after use.
  • Coverage (50 lb. bag):
    • Base coat – 225 square feet at 1/16 inch dry-film thickness
    • Top coat – 450 square feet at 1/32 inch dry film thickness
    • Coverage will vary depending on surface texture and porosity.

Damtite® Foundation Coating

  • Heavy, cement-based coating.
  • Bonds well with concrete and masonry substrates.
  • Recommended for concrete, masonry, basement walls, and foundation and retaining walls.
  • Resistant to both positive and negative hydrostatic pressure.
  • Will not “blow off” exposed side of wall.
  • Breathable; allows interior moisture to escape without damaging coating.
  • Locks deep into pores and voids to become part of the wall when fully cured.
  • Gray in color to blend into cement block and concrete walls.
  • Resistant to mold and mildew.
  • Apply with a push broom or 6” masonry brush.
  • Can also be mixed with clean washed sand and trowel-applied as a superior waterproofing coating.
  • This is the best product we know of for bonding styrofoam to the outside of masonry walls.
  • Can be used above grade, but not intended as a decorative finish coat.
  • Comes in dry powder form; mix with water.
  • Cleans up with soap and water immediately after use.
  • Coverage (50 lb. bag):
    • Base coat – 225 square feet at 1/16 inch dry-film thickness
    • Top coat – 450 square feet at 1/32 inch dry film thickness
    • Coverage will vary depending on surface texture and porosity.

Damtite® High Strength Bonding Primer Adhesive

  • Permanently bonds new concrete and plaster to existing.
  • Eliminates the need to roughen surfaces before applying topcoat.
  • Use as prime coat or adhesive for concrete, plaster and stucco mixes.
  • Super high strength.
  • Apply by brush, roller, or spray.
  • Can be applied to dry or damp surfaces.
  • Cleans up with soap and water immediately after use.
  • Coverage: 150 to 300 square feet per gallon, depending on porosity and surface texture.

Damtite® Bonding Additive

  • Acrylic polymer, water-based liquid.
  • Mix with any cement-based material to improve adhesion, cohesion; tensile, compressive, and flexural strength.
  • Recommended for cement mortars, plasters, stuccos, concrete mixes, and most cement-based materials.
  • Add to concrete for resurfacing driveways, floors, or walks.
  • Promotes long-lasting repairs.
  • Adds extra toughness and crack-resistance to cement-based mixes.
  • Use for interiors or exteriors; above or below-ground.
  • Improves freeze/thaw stability of cement-based materials.
  • Ideal where hard, strong, fast-curing material is required for patching, repairing, or surfacing.
  • Milky white, colorless and non-yellowing to mixture.
  • Stable, will not re-emulsify when exposed to water.
  • Easy to use; one component-liquid mixes easily with water.
  • Use straight in place of water for tough bonding problems or mix equally with water for large overlays.
  • Cleans up with soap and water immediately after use.
  • Coverage will vary depending on the suggested mixing ratio for particular uses.

Damtite® Hydraulic Cement

  • Portland-cement-based repair mortar to repair holes or cracks flowing with water.
  • Use above or under water or where water is flowing under constant pressure.
  • Recommended for masonry, concrete, basements, foundations, retaining walls, sewers, sea wells, water storage facilities, tunnels, fountains, water channels and rains, ponds, and piers.
  • Suitable for drinking water systems.
  • Quick-setting, non-shrinking, permanent.
  • Expands as it hardens to lock in place and form a perfect seal.
  • Dries in 3 to 5 minutes.
  • Use interior or exterior; above or below-grade; vertical or overhead on non-moving cracks or joints.
  • Completely waterproof, suitable for immersion service.
  • Easy to use; one-component powder mixes easily with water.
  • Cleans up with soap and water immediately after use.
  • Coverage: 2-1/2 pounds fills approximately 39 cubic inches.

HENRY® 527 TileFlex Plus™ Flexible Thinset Mortar

  • Portland cement-based.
  • Used for the installation of porcelain, quarry, stone, ceramic, and mosaic tile over most interior and exterior surfaces.
  • Can also be used to install porcelain tile over interior plywood floors.
  • Coverage: 90 to 100 sq. ft. per 50 lbs. bag with 1/4”x1/4”x1/4” square-notched trowel.

HENRY® 544 Floor Leveler Self-Leveling Underlayment

  • Cement-based.
  • Use to level and smooth interior concrete and other surfaces prior to the installation of ceramic tile and other floor coverings.
  • Hardens quickly and is walkable in 4 hours, allowing tile to be installed in 6 to 8 hours.
  • Covers 40 sq. ft. at 1/8” thickness.

HENRY® 547 UniPro™ Universal Underlayment

  • Cement-based.
  • Used as a patch, underlayment, or embossing leveler.
  • Bonds to concrete, wood, steel, stainless steel, brass, lead, ceramic, terrazzo, existing “cutback” residue and existing resilient (as an embossing leveler) on all grade levels as recommended; metal substrates must be clean and abraded.
  • Extremely versatile.
  • High compressive strength.
  • Fast-setting.
  • Excellent fill characteristics; non-shrinking.
  • Non-sanded formation.
  • Click herefor more information.

HENRY® 549 FeatherFinish™ Underlayment Patch & Skimcoat

  • Portland cement-based.
  • Use for patching, skimcoating, and featheredging interior concrete, masonry, wood, cementitious terrazzo, and ceramic tile.
  • Can also use to smooth ridges or to fill cracks, gouges, and joints.
  • Provides a smooth and permanent finish prior to the installation of floor coverings.
  • Can be applied to any prepared surface using a steel trowel.
  • Dries in 15 minutes; allows floor-covering installation to proceed with minimum delay.
  • No primers or additives needed.
  • Will not stain or mildew.